Your one-stop shop for all of your Radio needs!
Please PRAY for our Friends at RigExpert in Ukraine.
LOOKING FORWARD TO SEEING ALL OF OUR FRIENDS AT KNOXVILLE TN HAMFEST THIS WEEKEND.
FREE SHIPPING ON MOST ORDERS OVER $100.00 IN THE LOWER 48 STATES.
IF THINGS WERE NOT ALREADY BAD ENOUGH THE USPS HAS PUT A SURCHARGE ON ALL BOXES AND TUBES OVER 24" LONG. YOU WILL SEE THIS ADDITIONAL SHIPPING CHARGE ON ANTENNAS AND MAST. WE ARE SORRY BUT ITS OUT OF OUR HANDS.
WE ARE MOVING TO START SHIPPING MOSTLY FEDEX IN THE COMING MONTHS. PLEASE MAKE SURE YOU INCLUDE YOUR PHONE NUMBER IN THE ORDER. WE WILL NOT CALL YOU OR SHARE YOUR NUMBER UNLESS ITS A NECESSITY. THANKS FOR UNDERSTANDING.
WE SHIP TO ALL 50 STATES AND US TERRITORIES.
CANADIAN ORDERS PLEASE CALL FOR SHIPPING QUOTES.
HAVE QUESTIONS? CALL US 1-833-456-4673 TOLL FREE
The WCS-V86 Radio Programming Software is designed to give you the ease and convenience of programming the memories and set menu options of your radio from your PC. Any memory channel with all its details can be sent to the radio with a simple keystroke.
Memory Channels Include:
Other Menu Item Categories Include:
The Radio Programmer Is for so Much More than Just Memory Management.
The programming process begins by first installing the program then installing (and allowing) the drivers for the cable. Be sure to complete both of these steps.Next, make all the connections between the radio and the computer and complete Communications | Get data from radio. This “syncs” the radio and computer. Even if the radio is not yet set up with memory channels, there are details that the programmer needs to get from the radio.Start setting up details for your radio in a “factory fresh” file (File|New) or in the file that was created when you did Communications | Get data from the radio. Begin by entering a receive frequency (that will be the frequency published for the repeater). When you press Enter or Tab to leave the Receive frequency field, the program will complete details for the channel. Then customize Name and Tone to match the details you have for that local repeaters.Use the links to external data sources (File | External data) built right into the programmer to access repeater details for your area or for a location you plan to visit. Then with just a few button clicks, you have a file with hundreds of entries and all you typed was your location (i.e., zip code or city).
Save your file as you work. This is a computer, after all, and you would hate to lose your work should the system fail. Actually, create and save as many files as you want or need. You could have one file for home, a different one for the vacation house, another for the trip to your son’s house, another for the yearly 3K run and picnic where you help direct traffic and want the radio to be programmed with only the frequencies for that event. Remember, radio programming is an overwrite process. Everything in the radio is replaced by everything in the file.
Limit Memories are used by the radio for Program Scan. Program the same details for Limit Memories as for regular memory channels. Many of the Limit Memories are preprogrammed in the radio and while the frequency can be changed to another within the band, they cannot be left blank.
Home/Call channels are special memories accessed through one button recall on the radio. These channels are preprogrammed in the radio and while the frequency can be changed to another within the band, they cannot be left blank.
Radio Menu Settings
Use this screen to customize many set menu features of the radio. Check boxes toggle features on or off, use drop down menus list all selections and blank boxes for personalized entry add to the ease of setting up your radio exactly like you want it.
The entries on the Settings screens are made for you to “Set and Forget”. Once settings are customized, you are prompted to save before exiting. The saved settings will be there every time you create a new frequency file.
Enter DTMF memory details to customize options for this functions of the radio.
RT Systems Programmers interface with four sources of data to make it easy for you to find repeater information. Some of these sources even include information for repeaters outside the US. Your existing subscription to a service (where required) works in the programmer.
Radio Reference Search
An internet connection and subscription to the service are required for this search.Enter the user e-mail and Password that you established when you purchased your subscription from RadioReference Then select the State– Select the state from the list and County– Select the state from the list to get repeaters for that area.Click OK.
Repeater Book Search
An Internet connection is required for this search.Location – Enter City, State, Country (if not in the US).Radius – Enter how many miles (up to 90 maximum) around this location.Select Bands – This is not terribly important since it can be done on the next screen; however, you might want to limit the selection to reduce the number of repeaters in the results. Uncheck All Bands to make the individual bands active.Click OK.
An internet connection and subscription to the service are required for this search.Enter the User E-mail and Password that you established when you purchased your subscription from RFinder.Location - Search around a specific city. Enter City, State and Country (if not US). Enter Radius up to 90 miles.Route - Search along the route of a trip you’re planning. Enter the Start and End cities, a width (remember to limit this since you can’t hear repeaters that are too far away), and waypoints (other cities along the way). The search will travel along major interstate highways between the two cities. If the result is not along the route you plan to take, enter other waypoints on your route.Map Route – Use this option to see the route the search will take. Close the map to return to the search screen.Click OK.
The information is returned on a screen that is not yet ready for radio programming, this screen lets you examine the data to see if the results are about what you expected. You might find that you spelled the city name wrong which resulted in nothing being returned; or that you want to pull repeaters from further away; or you want to get repeaters for different bands.Select what the radio uses as the Name display. You can select the Callsign (default), City, State, Region, Repeater Notes or Sponsor. Notice that each of these categories is a column of information in the grid. You will see those names at the top of the screen. You are selecting the information in that column for the Programmer to set up for the Name field. NOTE: The radio will truncate (cut off) the information in the field at the maximum number of characters it can use for the Alpha/numeric display. You might end up with only the first four or six characters of the information in the column. Consider this when selecting the information.Select what the Programmer will use in the Comment field. This information does not go to the radio but can be very helpful for identifying a channel as you work with it on the spreadsheet. You can print this information along with other details for the channels to have it on hand as you travel. Again, select Callsign, City, State, Region, Repeater Notes or Sponsor.
Sorting Return Data
The screen that opens after you click OK for one of the external data searches gives you the ability to remove repeater information that your radio cannot use. You might have a radio that does not do DMR, DStar or Yaesu Fusion. Simply uncheck these in the list. The channels are removed from the list automatically.Once you finish eliminating frequencies or modes your radio cannot use, select your radio from Modules and then click Create file for (your radio).
After clicking Create File for (Your radio) the programmer creates the file that you use to program your radio. Notice that all the Tones are set up with the tone frequencies. All done automatically.What a list and all you did was enter a location!
Preferences Customize the Programmer
When I received my call sign a few years back, I was flooded with purchases of junk. Fast forward to 2019. I decided I wanted to build another option, not a dealer who has the same stuff as everyone else, but a dealer who actually uses what he sells. And that’s exactly what I do. If you see a product on this page or one of our tables at Hamfest, you can bet we have tried it and like it. From Radios to connectors we strive to bring you QUALITY. Sure, you can find it cheaper and we understand that, but if you don’t want to buy it again in 6 months, take a look at what we sell and have already approved. I am always just a phone call away. Jim Gifford, KM4MPF.
CALL US AT 1-833-4-KM4MPF / 1-833-456-4673 AND FIND OUT WHEN WE WILL BE AT A HAMFEST NEAR YOU.
4000 7th ave
Chattanooga, TN. 37407
9:00 till 4:00